山東裝載機輪胎屬于易耗品，在使用過程中難免會出現輪胎損壞的情況，進而影響輪胎的正常使用，很多人不了解輪胎損壞的原因，造成了很大的經濟損失，如果在平時使用中多加注意和保養能大大延長輪胎的壽命。那么引起裝載機輪胎損壞的原因有哪些呢？

1、輪胎氣壓不足
這樣會使得裝載機負荷增大，導致輪胎變形，進而增加輪胎行駛時磨損面積，另外頻繁轉向也會導致胎壓不足的輪胎磨損加劇。
This will make the loader load increases, leading to tire deformation, thus increasing the area of the tire with wear, in addition to insufficient tire pressure frequently turn will lead to increased tire wear.
2、路面平整度差
裝載機長期行駛于巖石、沙石等物料場地，其堅硬的棱角刺入胎冠表面膠體形成創口。
Loaders long-term travel in rocks, sand and other materials venues, its hard edges piercing wound tread surface colloid formation.
3、胎冠膠體不規則脫落
路面條件較差會導致輪胎出現膠體脫落，胎冠異常磨損就會進一步加劇。翻新輪胎原有的胎體存在硬傷，胎冠耐磨性差，在外力作用下自然脫落。
Poor road conditions can cause the tires appear colloid off, abnormal tread wear will be further intensified. Retreaded tire carcass original existence flawed, poor tread wear, under loads fall off naturally.
4、扎胎
裝載機行駛過程中，突出路面的帶棱角的碎石、鋼筋、螺桿、釘子等細長物料，如果角度合適，極易刺透胎體，傷及內胎，造成內外胎同時損壞。
Loader driving, highlight road gravel, steel, screws, nails and other materials slender angular, if appropriate angle, easily pierce the carcass, hurt inner tubes, tires and tubes simultaneously causing damage.
5、未及時調整或更換
大多數裝載機駕駛員在輪胎使用過程中存在不爆胎不更換，當裝載機進行舉升作業時，鏟斗裝載物料以及舉升裝置的大部分負荷分別作用于兩側輪胎，由于輪胎高度的差異，導致整個舉升裝置無法保持縱向垂直于地面，對輪胎造成磨損，降低使用壽命。
Most loader driver exists in the course does not puncture the tires are not replaced, when the loader were lifting operations, as well as most of the loading bucket load lifting device were acting on both sides of the tires, because of the height of the tire differences, leading to the lifting device can not maintain vertical perpendicular to the ground, causing tire wear and reduce service life.
 

山東裝載機：http://www.greennutrition.cn/