裝載機冬季保養必不可少，在裝載機停止工作的期間，要提前更換相應的柴油和潤滑油，那么具體的細節該怎么做呢？

一、選擇優質防凍液

衡量防凍液主要有兩個指標：一是冰點，普通型防凍液可達到—40℃，而優質防凍液能達到—60℃左右；二是沸點，防凍液至少應達到108℃。
Antifreeze measure has two main indicators: First, freezing, ordinary type of antifreeze can reach -40 ℃, and quality antifreeze can reach -60 ℃; Second boiling point, antifreeze should reach at least 108 ℃.
二、水泵檢查
有些設備在更換防凍液后出現機油內有防凍液的現象，這是由于水泵水封老化失效，造成防凍液通過水封進入潤滑腔，最終到達油底殼內。因此更換防凍液后應密切觀察機油油位。發現油位升高，應停機檢查，一般采用更換水泵水封或水泵總成方法。修復后要在機器空載怠速運轉下，用新機油帶走進入發動機潤滑系統殘留的防凍液，注意：縮短下次更換機油的間隙時間，以確保發動機潤滑系統正常發揮功效。
Some devices have appeared in the replacement of antifreeze in the antifreeze oil phenomenon, which is due to the aging of the pump seal failure resulting antifreeze into the lubrication chamber through the seal, and finally to the oil sump. So after replacing antifreeze oil level should be closely observed. Found that the oil level rises, should stop to check, generally used to replace the water pump seal or pump assembly methods. To repair the machine after idling under load, with the new oil into the engine lubrication system away residual antifreeze Note: the next oil change interval shorter time to ensure normal functioning of the engine lubrication system effectiveness.
三、冷卻系統防腐濾芯
冷卻系統防腐濾芯含有離子交換樹脂、防蝕劑、鎂板等添加劑，可以有效保護有關部件。離子交換樹脂可防止水垢的形成。防蝕劑可以在冷卻液套中形成防蝕膜以防止氧化。因為鎂的金屬活性比鐵強，冷卻液中的腐蝕性離子首先與鎂板發生反應，有效防止鐵被腐蝕。另外防腐濾芯還能過濾鐵銹、水垢和泥沙。防腐濾芯須與防凍液同期更換，而且防腐濾芯應第1000小時（發動機工作時間）更換，確保防腐濾芯起到有效保護作用。
Cooling system corrosion cartridge containing an ion exchange resin, a corrosion inhibitor, and other additives magnesium plate, can effectively protect the relevant member. Ion exchange resin prevents the formation of scale. Corrosion inhibitor film can be formed in the coolant jacket in order to prevent oxidation. Because magnesium metal active than iron, corrosive coolant magnesium ion reaction occurs first plate to effectively prevent corrosion of iron. Another filter can filter corrosion rust, scale and sediment. Preservative filter must be replaced with the same period in antifreeze and corrosion protection filter should first 1000 hours (engine hours) replacement to ensure corrosion protection filters play an effective role.
四、潤滑油選用
應根據當地氣溫，結合潤滑油的凝點、傾點和黏度選用合適的潤滑油。凝點高的潤滑油不能在低溫下使用。相反在氣溫較高的地區則沒有必要使用凝點低的潤滑油。凝點和傾點都是潤滑油低溫流動性的指標，兩者無原則性的性別，只是測定方法稍有不同。同一潤滑油的凝點和傾點并不完全相同，一般傾點都高出凝點2--3℃。
Should be based on the local temperature, combined with oil pour point, pour point and viscosity appropriate choice of lubricants. High pour point oil can not be used at low temperatures. At higher temperatures the opposite region is not necessary to use a low pour point oil. Pour point and the pour point is the indicator of the low temperature fluidity lubricants, there was no gender principle, only slightly different measuring methods. Same oil pour point and pour point are not identical, are generally higher pour point pour point 2 - 3 ℃.
六、設備三漏檢修
熱脹冷縮現象在液壓系統、氣路、水路的密封件，尤其是橡膠類O型圈、矩型圈等密封件上表現更為明顯，氣溫持續低于0℃時，機器會出現漏油、漏氣、漏水現象，特別是氣溫持續接近-10℃時。在設備進入冬季前要對整機三漏情況進行全面檢修，排除三漏故障和隱患故障。
Thermal expansion and contraction phenomena in the hydraulic system, gas, water seals, especially on the rubber O-ring, rectangular ring seals to become more evident, the temperature remained below 0 ℃, the machine will appear spill , leakage, water leakage, especially when temperatures consistently close to -10 ℃. In front of the whole device into the winter to conduct a comprehensive overhaul of three missing exclude leakage of hidden faults and failures.
七、檢修電氣設備
冬季老化設備多發生啟動困難故障，因此前的換季保養時檢查并更換老化電氣線路和部件是減少啟動困難一個必不可少的舉措，還需徹底檢查保養蓄電池。暖風設備是冬季戶外作業必不可少的，因此在嚴冬之前應檢查暖風設備工作情況，修復暖風設備。
Winter aging equipment malfunction occurred difficult to start, so check and replace aging electrical wiring and components are essential to reduce the difficulty in starting a pre-season move when maintenance needs thorough inspection and maintenance batteries. Heating equipment is essential for outdoor work in winter, so you should check before winter heating equipment work, repairing heating equipment.